Clicky

Fire-Rated Acoustic Panels: Reading EN 13501-1 and Fire Resistance

Fire rated acoustic panels EN 13501-1: MST PET felt acoustic panel catalogue

A specification calls for acoustic panels to be “fire rated.” A distributor forwards a datasheet with one line — B-s1,d0 — and the fire engineer asks whether that also satisfies the 60-minute wall the panels are being fixed to. The procurement manager wants a single document for the tender pack and receives three, none of which describe the exact panel being purchased. This is where enquiries about fire rated acoustic panels EN 13501-1 go wrong: the classification is real, but it answers a narrower question than most buyers assume. This guide is written for architects, acoustic consultants, main contractors, distributors and purchasing managers who need to specify, document and defend a fire requirement without discovering a gap at submittal.

We write from the supplier side, for people who sign off specifications rather than decorate a home studio. The figures and class targets below are indicative planning guidance only; the classification, report and quotation issued for your exact construction are always the controlling source. We quote no certificate numbers and reproduce no test reports here — those must come from the manufacturer for the panel you are actually buying. For product context before you read on, see the PET felt and fabric panel category.

What EN 13501-1 actually classifies — and what it does not

EN 13501-1 is the European classification standard for the reaction to fire of construction products. Reaction to fire describes how a material behaves when it is itself exposed to fire: how readily it ignites, how quickly flame spreads across its surface, how much smoke it produces and whether it sheds flaming droplets. It is a property of the product as tested, under a defined mounting and a defined construction.

It is not a measure of how long a wall, floor or ceiling assembly can keep fire from passing through it. That is fire resistance — the ability of a constructed element to maintain integrity, insulation and, where relevant, loadbearing capacity for a stated period, expressed as EI or REI ratings under standards such as EN 13501-2. The two ideas are related but not interchangeable, and confusing them is the single most common cause of a failed fire submittal. A decorative panel that carries an excellent reaction-to-fire class does not, by itself, turn a partition into a 60-minute fire-rated assembly; it must be detailed as part of a tested system, with fixings, joints, penetrations and cavity barriers accounted for.

Keep that distinction in mind every time a datasheet says “fire rated.” Ask which of the two the number refers to, and who tested the assembly. When the panel is intended to sit on a rated lining, request the fixing and junction detail from the supplier and have the design team confirm it against the rated system. Application notes that follow this supplier-side approach are collected under solutions.

Fire rated acoustic panels EN 13501-1: decoding the Euroclass label

A classification such as B-s1,d0 is three pieces of information compressed into one code. Reading each part lets you judge whether a panel fits the room rather than simply chasing the “highest” class.

  • The main class (A1, A2, B, C, D, E, F). This describes contribution to fire, measured with tests including the single burning item (SBI) test, EN 13823, supported by small-flame testing. A1 is non-combustible; B is very limited contribution; the scale descends to F, for which no performance is determined.
  • The smoke suffix (s1, s2, s3). s1 is the lowest smoke production, s3 the highest. Smoke behaviour matters most in escape routes, cinemas and other spaces where visibility during evacuation is critical.
  • The droplet suffix (d0, d1, d2). d0 means no flaming droplets or particles. This is especially important for ceiling-mounted products such as baffles and clouds, where burning material falling from above is a secondary hazard.

For wall and ceiling linings in offices, schools, healthcare and public assembly buildings, specifiers commonly call for B-s1,d0 or better in the European system; corridors and escape routes are usually the strictest. Treat that as an indicative industry starting point, not a universal rule: national implementations differ and the fire engineer for the project sets the actual requirement. The important discipline is to write the suffixes in full. A datasheet that says only “Class B” has told you nothing about smoke or droplets.

Fire rated acoustic panels EN 13501-1 in PET felt colour options
Euroclass results apply to the exact construction, so check the finish against the report.

Reaction to fire vs fire resistance: the distinction approvers check

When a submittal is reviewed, the approver is asking two separate questions. First: is the product’s reaction-to-fire classification appropriate for this room and this surface? Second: does the construction it is fixed into still achieve the required fire resistance once the panel, its fixings and its joints are introduced? A complete package answers both. Here is the distinction in practical terms.

Aspect Reaction to fire (EN 13501-1) Fire resistance (e.g. EN 13501-2)
Question answered How does the product behave when exposed to fire? Can the element stop fire passing for a given time?
Typical result Euroclass A1–F plus s1–s3 and d0–d2 EI or REI rating in minutes (30, 60, 90…)
Applies to The panel or facing as a product A tested wall, floor or ceiling assembly
Affected by Material, thickness, density, coating, backing Layer build-up, fixings, joints, penetrations
Who confirms it Product classification report from a laboratory System test report or assessment from the system designer
Common error Quoting a headline class without suffixes Assuming a panel class upgrades an assembly rating

The last row is the one that costs projects time. A panel with B-s1,d0 does not “make” a wall into EI 60. If the wall behind it is rated, the panel is part of the lining build-up and must be included in the assessed system, with the fixing pattern and any cavities detailed accordingly. If the panel is a decorative facing on a non-rated partition, no resistance rating is being claimed at all — and the specification should say so. Clarity at this stage prevents an approver from returning a package with a query that could have been answered in the first submission.

ASTM E84 Class A and how it relates to Euroclass

North American projects generally reference ASTM E84, the surface-burning test that produces a Flame Spread Index and a Smoke Developed Index, grouped into Class A, B or C. Class A is the usual default for commercial interiors. Buyers often ask whether Class A “equals” B-s1,d0. It does not: the test methods, sample mounting and classification logic are different, so there is no clean conversion between the systems.

The practical answer is to hold documents for both markets when you distribute internationally, and never to substitute one report for the other in a submittal. A supplier serving global projects should be able to provide the European classification report and the ASTM E84 result for the same construction, and should state plainly which variant each report covers. If only one system is documented, flag it early — a request for a report that does not exist will stop a submittal whatever the material’s real performance. For finishes and colour options that must be checked against the tested construction, the custom colour acoustic felt panel page shows how a stocked finish range is handled.

How the substrate and build-up change the result

A fire classification belongs to a specific construction, not to a material name. Change the facing, the core density, the backing, the adhesive or the thickness and you may have a different product in the eyes of the test. This is why a report for one variant cannot be assumed to cover another, and why “the same panel in a different colour” is a question worth asking rather than an assumption worth making.

Three variables do most of the work. Thickness and density affect how quickly a panel heats through and how much fuel it contributes. The backing layer — a PET felt backing, a mineral wool layer, or an open air gap — changes heat release and smoke behaviour behind the facing. The facing and finish, including any coating, print or veneer, sit closest to the flame and can dominate the result. A perforated or slatted timber face over an absorptive backing behaves differently from a flat felt panel, so compare like with like. The mineral fibre ceiling category illustrates one family where the core material itself is chosen for its fire behaviour.

Reaction to fire and substrate of mineral fibre acoustic panels
Core and backing material influence the reaction-to-fire result of a panel build-up.

Ask the supplier to state the exact tested construction in writing: facing, core, backing, adhesive, thickness and mounting. Then check that the panel on your schedule matches it. If it does not, request the report for the variant you are buying or a written assessment that covers the change. This is neither distrust nor pedantry — it is the difference between a document an approver accepts and one they return.

Fire rated acoustic panels EN 13501-1 documentation for tender submissions

A tender package is judged on completeness, not on the number of documents in it. Assemble a short, labelled set in which every file refers to the same product reference used on your schedule. Use this checklist as the minimum scope to request from a supplier.

  • The reaction-to-fire classification report for the exact panel construction, stating the laboratory, report reference and date.
  • The classification result written in full, including smoke and droplet suffixes, not a shortened headline class.
  • ASTM E84 results for North American projects, reported as indices as well as a class.
  • A Declaration of Performance where the product falls under a harmonised standard and CE marking applies.
  • A statement of the mounting condition and tested thickness the data relates to.
  • Fixing and junction details where the panel sits on or near a fire-rated assembly.
  • A technical data sheet whose product reference matches the schedule and the reports.
  • A written confirmation of which variants — colours, finishes, thicknesses — are covered by each document.

Keep the set together and index it against the panel schedule. If a review body raises a query, a labelled set can be answered in hours; a loose folder of unrelated PDFs takes weeks. Catalogue and technical documents are gathered on the resources page, which is the natural place to start when you are assembling a package.

MST catalogue with acoustic panel fire certificate and specification documents
Keep classification, acoustic data and finish references in one indexed document set.

Application scenarios: where the fire requirement drives the specification

Different rooms put different weight on different parts of the classification. In a hospital corridor or an escape route, smoke production is as important as the main class, because evacuation depends on visibility; specify the s-suffix explicitly. In a cinema or auditorium with ceiling-mounted absorbers, the droplet suffix matters for the same reason falling material is a hazard, so d0 is usually written in. In a school or office fit-out, the common requirement is a limited-combustibility lining with low smoke, and the review focuses on whether the exact facing and backing were tested together.

Acoustic performance and fire performance must be checked side by side, because the constructions that improve one can affect the other. An air gap behind a panel can raise low-frequency absorption, but it also introduces a cavity that must be detailed correctly in a rated assembly — see the wood wool acoustic panel range for a product family where material and build-up are chosen together. Where the surface is also a design feature, such as a printed or faced panel, confirm that the finish is part of the tested construction rather than an afterthought. The aim is a single schedule on which acoustic data, fire documents and finish references all point to the same product.

Common mistakes when specifying fire rated panels

The first mistake is accepting a headline class without its suffixes, which hides the smoke and droplet behaviour. The second is treating a reaction-to-fire class as a fire-resistance rating for the building element — the two answer different questions. The third is borrowing a report from a different thickness, finish or backing because the panel “looks the same”; it rarely is, in test terms. The fourth is leaving the mounting condition unstated, so the data is compared against an installation that was never tested. The fifth is assembling the fire documents after the schedule is frozen, then discovering that a chosen colour or coating is outside the tested variant. Every one of these is avoidable if the construction is fixed early and the documents are requested against it.

Request a quote and the fire documentation pack

To scope a project properly, send the panel schedule, the required classification written in full, the room and assembly context, and the target submittal date to the MST Acoustics quotation team. We will confirm which documented construction matches your specification, state the variants covered by each report, and return an indicative package with fire documents, acoustic data and commercial terms shown as separate lines. If you are still defining the requirement, download the catalogue and technical documents from the resources page first. All classes and figures here are indicative guidance only; confirm every classification, report and price in the formal quotation issued for your project.

Frequently asked questions

What does B-s1,d0 mean for fire rated acoustic panels EN 13501-1?

It is a three-part reaction-to-fire classification. B is the main Euroclass for contribution to fire, s1 is the lowest smoke-production suffix and d0 means no flaming droplets. Write all three parts into the specification; a datasheet that says only ‘Class B’ omits the smoke and droplet behaviour that approvers need to see.

Is EN 13501-1 the same as a fire resistance rating?

No. EN 13501-1 classifies how a product reacts to fire when exposed to it. Fire resistance describes how long a constructed element such as a wall or ceiling can resist fire passing through it, expressed as an EI or REI rating. A panel’s Euroclass does not upgrade an assembly’s fire resistance; the panel must be detailed as part of a tested system.

Does ASTM E84 Class A equal a Euroclass B-s1,d0 panel?

There is no direct conversion. ASTM E84 produces a flame spread and smoke developed index under a different test method and mounting, while EN 13501-1 assigns a Euroclass with smoke and droplet suffixes. For international projects, request documents for both systems for the same construction rather than substituting one report for the other.

Does the substrate or backing change a panel’s fire classification?

Yes. A classification belongs to a specific build-up: facing, core, backing, adhesive, thickness and mounting. Changing the backing layer, a coating or the thickness can change the result, so a report for one variant does not automatically cover another. Ask for the tested construction in writing and check it against your schedule.

What fire documents should be included in a tender submission?

Include the classification report for the exact panel construction with all suffixes written out, any ASTM E84 results, a Declaration of Performance where applicable, the tested thickness and mounting condition, fixing details near rated assemblies, and a data sheet whose product reference matches the schedule. Index each document against the panel schedule.

Can a decorative finish affect the fire performance of an acoustic panel?

It can. A coating, print or veneer sits closest to the flame and can influence the classification, so the finish should be part of the tested construction rather than applied afterwards as an untested extra. Confirm with the supplier which colours and finishes are covered by each report before you freeze the specification.

Leave a Replay

Sign up for MST acoustic panel news

Know more MST & Acoustic Material.

Contact us

Get in touch with acoustic material expert.